I/O-moduler för PAC

8-channel Vibrating Wire Extended Board.

The e-USB404 CR adds four independent USB 3.1 Gen 1 host controllers to an AXP-9000-IoT Programmable Automation Controller through a single e-Bus x4 slot. It suits engineers who need several USB devices running at the same time, particularly USB vision cameras that generate large volumes of image data.Each port has its own controller and an LED status indicator, and all four Type-A connectors are accessible on the panel for straightforward wiring. Each port supplies 5 V at up to 900 mA, with overload and short-circuit protection. Power to each port can be switched on and off in software through the SDK, which allows a hung USB device to be reset for failure recovery.Transfer modes: SuperSpeed (5 Gbps), High Speed (480 Mbps), Full Speed (12 Mbps) and Low Speed (1.5 Mbps)Supported on Microsoft Windows 7/8.1/10 and LinuxOperating temperature -25 ~ +60 °CTypical uses are frame grabbing in machine vision inspection, automated optical inspection, quality assurance and medical imaging.ApplicationsMachine vision inspectionAutomated optical inspectionQuality assuranceMedical imaging

The I-8014CW-G CR is an analog input module for engineers who need fast, accurate current measurement across eight differential channels. Each channel is sampled with 16-bit resolution, and single-channel pacer mode reaches 250 kS/s, with a ±20 mA input range and 2500 VDC intra-module isolation.The Magic Scan function lets individual channels be scanned at different input ranges while keeping the sampling rate at 250 kS/s during single-channel scans. It can run as a standard scan or as a Virtual Sample and Hold function, which offers a lower-cost alternative to hardware sample-and-hold on many analogue cards.A 4 K-sample onboard FIFO buffer stores conversion results. When the sample count passes a pre-defined FIFO level, an interrupt notifies the host. Combined with post-trigger external trigger mode and internal or external trigger start, this suits high-speed and time-critical acquisition tasks such as vibration analysis.ApplicationsHigh speed data acquisition systemsVibration analysis

I-8014W-G CR is a high-performance analog input module for engineers who need fast, accurate capture of voltage and current signals. It provides up to 16 single-ended or 8 differential inputs, selectable by jumper, with 16-bit resolution and a single-channel pacer sampling rate of 250 kS/s.The Magic Scan function lets each input channel use its own input range, and single-channel scanning keeps the full 250 kS/s rate. Magic Scan can run as a standard scan or as a Virtual Sample and Hold function, which offers sample-and-hold style operation without the cost usually associated with that feature on analog input cards.A 4 k-sample onboard FIFO buffer stores conversion results. When the sample count exceeds a predefined FIFO level, an interrupt notifies the host, which suits time-critical acquisition tasks such as vibration analysis. Internal or external trigger start and post-trigger external trigger modes are supported.ApplicationsHigh-speed data acquisition systemsVibration analysis

The I-8017DW-G is an analog input module for engineers who need fast, multi-channel acquisition from voltage or current sources. It accepts 8 differential or 16 single-ended inputs, with 14-bit resolution and a 100 kHz bandwidth.Each channel can be configured individually for ±10 VDC, ±5 VDC, ±2.5 VDC, ±1.25 VDC or ±20 mA. Current input is selected with a jumper, and the internal resistor for differential current measurement is also jumper-selectable. The module is supplied with voltage input selected by default. Sampling reaches 90 kS/s in single-channel polling mode, 50 kS/s in single-channel interrupt mode and 16 kS/s in 8-channel scan mode.Isolation is rated at 2500 VDC intra-module, and each terminal is protected against ±4 kV ESD contact discharge. The I-8017DW-G-G CR order includes a CA-4002F DB37 female connector with plastic cover, so it is ready for field wiring.ApplicationsHigh speed data acquisition systemsProcess monitoring and controlVibration analysisDigital pattern generation from a digital I/O port

The I-8017H CR is an 8-channel differential analogue input module for engineers who need fast, individually configurable measurement of voltage or current signals. Each channel can be set to its own input range, from ±10 VDC down to ±1.25 VDC, or to ±20 mA.Measurement performance is set by the 14-bit converter and the sampling mode in use. Single-channel polling reaches 100 kS/s, single-channel interrupt mode 50 kS/s, and the 8-channel scan mode 16 kS/s. Triggering can be internal or external. Input impedance (20 K, 200 K or 20 M) is selected by jumper.Current inputs require an optional external 125 Ω resistor, which must be fitted for current-source measurement. The module provides ±4 kV ESD protection on each terminal and 2500 VDC isolation between the module's internal circuits. This CR variant has a blue cover and carries CE, FCC, RoHS and WEEE marking.ApplicationsHigh speed data acquisition systemProcess monitor and controlVibration analysisDigital pattern generation from digital I/O port

The I-8017H-G is an 8-channel differential analogue input module for PAC I/O systems. Each channel can be set individually to one of several voltage ranges or to ±20 mA, which makes it practical where a single module must handle mixed sensor types.Sampling is available in three modes: up to 100 kS/s in single-channel polling mode, 50 kS/s in single-channel interrupt mode, and 16 kS/s when scanning all eight channels. Input impedance is selected by jumper, and triggering can be internal or external.Current input: current measurement requires an optional external 125 Ω resistor. The module is rated for an operating temperature of -25 ~ +75 °C and provides ±4 kV ESD protection on each terminal.ApplicationsHigh-speed data acquisitionProcess monitoring and controlVibration analysis

I-8017HCW-G is an analog input module for data acquisition tasks that need many channels and fast sampling. It accepts 16 single-ended or 8 differential inputs, and each channel can be configured individually for one of the ranges ±10 VDC, ±5 VDC, ±2.5 VDC, ±1.25 VDC or ±20 mA.The 14-bit converter samples at up to 90 kS/s in single channel polling mode, with a 100 kHz bandwidth. An internal jumper selects the differential current input resistor, and the module ships set for voltage measurement. The ordering code CR variant covers the standard configuration of this 20-pin terminal block version.Each channel is isolated with 2500 VDC intra-module isolation and protected against ±4 kV ESD contact discharge at each terminal, which suits electrically noisy industrial cabinets. The module is rated for an operating range of -25 ~ +75 °C and draws 2 W maximum.ApplicationsHigh speed data acquisition systemsProcess monitoring and controlVibration analysisDigital pattern generation from a digital I/O port

I-8017HW-G CR is a high-speed analog input module for data acquisition and control work where sampling speed and channel flexibility matter. It accepts 8 differential or 16 single-ended inputs, and each channel can be set to its own input range, from ±10 VDC down to ±1.25 VDC, or ±20 mA when current measurement is required.Single channel polling mode delivers up to 90 kS/s, with a 100 kHz bandwidth and 14-bit resolution. Input impedance is jumper selectable at 20 K, 200 K or 20 M, which helps match the module to the signal source. Current measurement depends on an optional external 125 Ω resistor, which must be fitted separately.The module provides 2500 VDC intra-module isolation and ±4 kV ESD protection on each terminal, and it has a 20-pin terminal block. Its operating range of -25 ~ +75 °C suits industrial enclosures.ApplicationsHigh speed data acquisition systemsProcess monitoring and controlVibration analysisDigital pattern generation from digital I/O port

8-Channel High Speed Thermocouple Input Module, Includes CN-1825 Daughter Board.

The I-8024UW-G is a source-type analogue output module with four single-ended channels, suited to engineers who need to drive voltage or current signals from an I-8K/I-87K PAC I/O arrangement. Each channel can be set to its own range, from 0 ~ +5 VDC and ±5 VDC through to 0 ~ +10 VDC, ±10 VDC, 0 ~ +20 mA and +4 ~ +20 mA. Output type is selected by jumper, and open wire detection is available on the +4 ~ +20 mA range.Each channel has a configurable power-on value and safe value, so outputs can start from a defined state and fall back to a known level. Short-circuit protection is fitted, and the module offers 2500 VDC intra-module isolation together with 3000 VDC isolation of the external power supply. Qualification for ±4 kV ESD contact protection at each terminal is also stated.The module is typically used in data acquisition, process monitoring and control, vibration analysis and factory automation. This ordering code is the RoHS-marked version of the module. Certifications listed for this model are CE, UKCA, FCC, RoHS and WEEE.ApplicationsData acquisition systemsProcess monitoring and controlVibration analysisFactory automation

I-8024W-G is a 14-bit analog output module with four single-ended sink channels. Each channel can be configured independently for ±10 VDC voltage or 0 ~ +20 mA current output, so a single module can handle either signal type without a separate module for each.The module offers RF immunity matching IEC 61000-4-3, ±4 kV ESD contact protection on each terminal and intra-module isolation. A 25 µs response time per channel supports fast output updates, and readback accuracy of ±1% of FSR allows output values to be verified.Suited to building, factory and machine automation I/OPart of the I-8K/I-87K High Profile seriesApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The I-8026W-G (ordering code I-8026W-G CR) puts six analogue inputs, two analogue outputs, two digital inputs and two digital outputs into a single module of the I-8K/I-87K series. It suits engineers who need mixed signal types on one High Profile unit rather than several separate cards.Each analogue input can be configured for its own range, from ±10 VDC down to ±1.25 VDC, or ±20 mA, and voltage or current operation is set with jumpers. The analogue outputs provide 12-bit resolution across ±10 VDC, ±5 VDC, 0 ~ 10 VDC, 0 ~ 5 VDC and 0 ~ 20 mA. Each analogue input withstands overvoltage up to 240 Vrms.The digital inputs are wet contact, sink/source type, with an ON level of +10 ~ 30 VDC. The digital outputs are isolated open collector sinks rated +5 ~ +30 VDC at 100 mA per channel, with overload and short-circuit protection. Intra-module isolation is 2500 VDC.ApplicationsIndustrial automationIndustrial machineryBuilding automationFood and beverage systemsSemiconductor fabricationControl systems

I-8028UW-G is an 8-channel analog output module from the I-8K/I-87K High Profile series for PAC and remote I/O systems. Each of its eight single-ended channels drives either a voltage or a current signal, so one module can serve mixed field devices such as valves, drives and indicators without needing separate hardware for each signal type.Output ranges are set per channel, covering 0 to 5 VDC, ±5 VDC, 0 to 10 VDC, ±10 VDC, 4 to 20 mA and 0 to 20 mA. Power-on and safe output values can be configured, so outputs can start from a defined level and fall back to a known state. Open wire detection is provided for the 4 to 20 mA range, and each output is protected against short circuits.The module suits data acquisition, process monitoring and control, vibration analysis and factory automation tasks where galvanic separation and 16-bit output resolution are required. Isolation is rated at 3000 VDC for the external power supply and 2500 VDC between internal sections, and the module is qualified for ±4 kV ESD protection on each terminal.ApplicationsData acquisition systemsProcess monitoring and controlVibration analysisFactory automation

I-8037W-G is a 16-channel digital output module for PAC I/O systems. Each channel is photocoupler-isolated and works as a source-type (PNP) output, so it switches the positive side of the load. Each channel can drive up to 100 mA across a load voltage of +5 ~ +30 VDC.Outputs are protected against short circuits, and power-on and safe digital output values can be configured, so the field side can be put into a defined state on start-up or during a fault. The module provides 3750 VDC intra-module isolation and ±4 kV ESD protection on each terminal, which suits electrically noisy industrial cabinets.The G variant in this ordering code is supplied with RoHS compliance noted in the product data. Status LEDs show power and communication, plus one indicator for each of the 16 I/O channels.ApplicationsIndustry automationIndustrial machineryBuilding automationFood and beverageSemiconductor fabricationControl systems

I-8040PW-G CR is a 32-channel digital input module from the I-8K/I-87K High Profile series, designed for +24 VDC input systems in industrial environments. Each channel is photocoupler-isolated, and the module offers 3750 VDC intra-module isolation together with ±4 kV ESD protection on every terminal.The input configuration can be set to sink or source through wiring, so one module can suit either wiring convention. Each channel accepts +19 ~ +30 VDC as ON and reads +11 VDC maximum as OFF. A low pass filter with settings from 1 ms to 70 ms, selected by jumper or CPU parameter, helps suppress noise, with a default of 10 ms.Optional daughter board connectivity, for example with the DN-37-381-A CR, to simplify field wiring.This variant suits building, factory and machine automation, as well as remote maintenance and diagnosis and test equipment.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

32 isolated digital inputs for wet contact signals. The I-8040W-A1-G CR accepts wet contact signals across 32 channels, with each channel photocoupler-isolated from the logic side. Input ON levels span +3.5 to +30 VDC, and the OFF threshold is below +1 VDC.Each input can be wired as either sink or source type, so the same module suits both NPN and PNP field devices without changing the hardware. Every terminal is rated for ±4 kV ESD contact protection, and the module provides 3750 VDC intra-module isolation.This ordering code includes the CA-4002F DB37 female connector. The module also supports an optional daughter board, such as the DN-37-381-A CR, which simplifies field wiring for multi-channel installations.ApplicationsBuilding automationFactory automationMachine automationRemote maintenanceRemote diagnosisTesting equipment

The I-8040W-G CR is a 32-channel digital input module from the I-8K/I-87K high profile series, designed for engineers who need many photocoupler-isolated wet-contact inputs in a single module. Each channel can be configured as a sink or source input through wiring, which suits both NPN and PNP sensor arrangements.Electrical protection is built in: every terminal is rated for ±4 kV ESD contact, and the module provides 3750 VDC intra-module isolation. Inputs read ON at +10 ~ +30 VDC and OFF at +4 VDC maximum, with an input impedance of 3 kΩ, 0.5W. Operating range is -25 ~ +75 °C.This ordering code includes the CA-4002F DB37 female connector. An optional daughter board, such as the DN-37-381-A CR, can be fitted to simplify field wiring. The module is certified to CE, UKCA, FCC, RoHS and WEEE.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The I-8041AW-G CR is a 32-channel digital output module from the I-8K/I-87K High Profile series. Each channel is photocoupler-isolated and works as a source-type (PNP) open collector output, rated for loads from +5 to +30 VDC at up to 100 mA per channel. Short circuit protection is provided on the outputs.Each output has its own LED, and a separate LED shows power and communication status, so channel activity can be checked at a glance during commissioning and fault finding. ESD protection of ±4 kV contact is provided on each terminal, and 3750 VDC intra-module isolation is included as standard.This CR ordering code includes the CA-4002F DB37 female connector with plastic cover. The module can also be paired with the DN-37-381-A CR daughterboard for easier wiring, or the DN-8K32R daughterboard where relay output is required.ApplicationsDigital output control within I-8K/I-87K series PAC I/O systems

The I-8041PW-G CR provides 32 photocoupler-isolated digital outputs in a single module, switching loads through open-collector sink (NPN) drivers rated for +10 ~ +50 VDC. Each channel handles up to 100 mA, making it suited to driving field devices such as indicators, relays and actuators from a 32-point output card.Protection is built in on every output. The module provides overvoltage protection at 60 VDC, overload protection at 1.1 A and short-circuit protection, so a faulty load is less likely to damage the output stage. A 3750 VDC intra-module isolation rating and ±4 kV ESD protection per terminal support electrically noisy installations.Each channel has an LED indicator for quick status checks, and a power and communication LED is also fitted. The CA-4002F DB37 female connector with plastic cover is included in this ordering code. The manufacturer also lists the DN-37-381-A CR daughterboard for easier wiring and the DN-8K32R for relay output.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The I-8041W-G CR is a 32-channel digital output module for switching loads in automation and control cabinets. Each channel is photocoupler isolated and uses a sink-type open-collector output, so it can drive loads from 5 to 30 VDC at up to 100 mA per channel.Each output is monitored by its own LED, and a separate LED shows power and communication status, which simplifies commissioning and fault finding. The module provides ±4 kV ESD contact protection on each terminal and 3750 Vrms intra-module isolation as standard.This ordering code includes the CA-4002F DB37 female connector with plastic cover. For wiring, the module can be paired with the DN-37-381-A CR daughterboard, or with the DN-8K32R if relay outputs are required.ApplicationsBuilding AutomationFactory AutomationMachine AutomationRemote MaintenanceRemote DiagnosisTesting Equipment

The I-8042 CR is a digital I/O module from the I-8K/I-87K low-profile series, combining 16 optically isolated digital inputs with 16 isolated open-collector outputs in a single unit. Its inputs are wet contact type and can be wired as sink or source, which suits mixed field wiring in automation cabinets.Each output channel is a sink-type (NPN) isolated open collector rated for a load of +5 ~ +30 VDC and up to 100 mA per channel. Photocoupler isolation, 3750 VDC intra-module isolation and ±4 kV ESD protection on each terminal help protect the module and the control system from electrical disturbance.The CR ordering variant ships with the CA-4002F DB37 female connector with plastic cover and is identified by its blue cover. The module draws 1.5 W maximum and is rated for an operating range of -25 ~ +75 °C.ApplicationsIndustry automationIndustrial machineryBuilding automationFood and beverageSemiconductor fabricationControl systems

The I-8042-G CR combines 16 photocoupler-isolated digital inputs and 16 isolated open-collector digital outputs on one module. It suits engineers who need switch and sensor signals and sink-type output loads handled in a single compact I/O point from the I-8K/I-87K low-profile range.Each input can be wired for sink or source operation, while the outputs are sink type rated at 100 mA per channel with a load voltage of +5 to +30 VDC. Every channel is isolated, with 3750 VDC intra-module isolation and ±4 kV ESD protection on each terminal. Power-on and safe output values are available as options, and 32 LEDs display power, communication and the state of every I/O channel.The module draws 1.5 W maximum and operates between -25 and +75 °C. This ordering code includes the CA-4002F DB37 female connector with plastic cover and uses the grey cover version of the module.ApplicationsIndustry AutomationIndustrial MachineryBuilding AutomationFood & BeverageSemiconductor FabricationControl System

The I-8042W-G CR is a 16-channel isolated digital input and 16-channel isolated digital output module for automation and control applications. Every input and output channel is photocoupler-isolated.Each input can be wired for sink or source operation, giving flexibility when matching field devices. The outputs are isolated open-collector, sink (NPN) type, with short-circuit protection. Power-on and safe values can be configured for the outputs, and 32 LED indicators show channel status.This ordering code includes the CA-4002F DB37 female connector with plastic cover. It is suited to the applications listed below.ApplicationsIndustry automationIndustrial machineryBuilding automationFood and beverageSemiconductor fabricationControl systems