Vibrationsövervakning

iSN-701-F15-L030 CR is a single-axis IEPE accelerometer for measuring vibration. It offers a ±80g amplitude range, a sensitivity of 100mV/g and a frequency response from 0.5Hz to 15kHz, which suits engineers who need to capture both low-frequency movement and higher-frequency vibration content in one sensor.The sensor uses a homotaxial construction and is rated IP68 without its cable. It measures Ø22.9 x 53.3 mm and is supplied with a 3 m cable. It runs from an 18 to 30 VDC supply drawing 2 to 10 mA, with a bias voltage of 10 to 14 VDC.The device is designed primarily for vibration analysis applications. The ordering code is the CR variant, and the page lists RoHS and WEEE compliance for this model.ApplicationsVibration analysis

iSN-701-F15-L060 CR is a 1-axis IEPE accelerometer aimed at vibration analysis. It measures up to ±80g with a sensitivity of 100mV/g, making it suited to engineers who need to capture vibration signals across a broad band.The sensor responds from 0.5Hz to 15kHz and uses a homotaxial design. It runs from a supply of 18~30VDC at 2~10mA, with a bias voltage of 10~14VDC for the IEPE interface.This CR variant ships with a 6 m (600 cm) cable. The housing measures Ø22.9 x 53.3 mm and is rated IP68 without the cable. The product is RoHS and WEEE certified.ApplicationsVibration analysisVibration monitoring

Magnetic Base for iSN-701-BALT series.

The iSN-701X converts a 1-axis IEPE accelerometer signal into eigenvalues that can be read directly over Ethernet or RS-485. The built-in 4 mA excitation current powers the sensor, and a 24-bit A/D converter handles the measurement, so the module can be connected to the accelerometer without a separate signal conditioner.Measured values are available through Modbus TCP on the RJ-45 port or Modbus RTU on the RS-485 port. The module also provides a threshold alarm: an alarm is raised when a vibration eigenvalue exceeds its configured limit. LED indicators show sensor Normal, Open and Short status.Engineers choosing this converter for vibration monitoring will find it suited to trend analysis, system monitoring and predictive maintenance schemes that need vibration data in a Modbus-based control or data system.ApplicationsBig data analysisSystem monitoringTrend analysisPredictive maintenance

The iSN-701X-mA converts a single-axis IEPE accelerometer signal into vibration eigenvalues that can be read over Ethernet or RS-485. It supplies 4 mA excitation to the sensor and digitises the signal with a 24-bit A/D converter, which suits high-frequency vibration measurement.Eigenvalues can be polled through Modbus TCP or Modbus RTU, and a threshold alarm is raised when a value exceeds its set limit. The module also provides a current output, so a controller without a communication interface can still use the vibration figure as a 0~20 mA or 4~20 mA signal.The DIN-rail housing accepts a +10 ~ +30 VDC supply and is rated for operation from -25 ~ +75 °C. Front-panel LEDs show power, sensor status (normal, open or short) and data acquisition activity, which simplifies commissioning and fault finding.ApplicationsVibration monitoringHigh-frequency vibration measurementCondition monitoring of rotating machinery with IEPE accelerometers

The iSN-703-F1-L015 CR is a triaxial accelerometer that measures vibration on three orthogonal axes at the same time, so one sensor can cover the full vibration profile of a machine or structure. Its MEMS element and 3-wire voltage output make it a practical choice for engineers who need a compact sensor for vibration analysis.Each axis offers a measuring range of ±18g and a sensitivity of 400mV/g, with a frequency response from 10Hz to 1kHz. The sensor has a bias voltage of 10±0.5VDC and runs from a 22 to 26VDC supply, drawing 3mA.The housing is rated IP67 and measures (15±0.05) x (21±0.05) x (8.5±0.05) mm (W x L x H). This ordering code includes a 1.5m (150 cm) cable and is RoHS compliant.ApplicationsVibration analysis

Magnetic Base for iSN-703-BALT series.

The iSN-711-MRTU CR is a self-contained vibration sensor module built around an onboard MEMS accelerometer. It measures along one axis, with an amplitude range of ±8g and a frequency range of 6 Hz ~ 1 kHz, which suits low-frequency vibration measurement on rotating and reciprocating machinery.Readings are made available over a single RS-485 port that acts as a Modbus RTU slave. A host controller or PLC can poll the sensor with standard Modbus RTU requests, using the serial settings N, 8, 1 and any baud rate from 9600 to 115200 bps. The module is powered from +10 ~ +30 VDC and draws 0.3 W.Mounting is flexible, with wall-mount or magnet adsorption options, and the housing measures 51 x 30 x 19 mm (W x L x H). It is rated for operating temperatures of -25 °C ~ +75 °C and humidity of 10 ~ 90% RH, non-condensing. Typical uses include monitoring production line equipment, motors and pumps, and other vibration monitoring systems.ApplicationsVibration monitoring systemProduction line equipment monitoringMotor and pump vibration monitoringReal-time factory machinery monitoring

iSN-711-MRTU-IP68 CR is a single-axis vibration sensor module for condition monitoring in harsh industrial settings. Its IP68 rating protects the housing against water, oil and dust, so it can be fitted close to the equipment it monitors.A built-in MEMS accelerometer measures vibration on one axis across 6 Hz ~ 1 kHz, with an amplitude range of ±8g. The module exposes a single RS-485 port with Modbus RTU slave protocol, so a master controller can poll the vibration data directly over the bus using standard Modbus RTU commands.Typical uses include production line equipment, motors and pumps, where engineers need to watch for changes in vibration. The module can be wall-mounted or fixed by magnet adsorption.ApplicationsVibration monitoring systemProduction line equipmentMotorsPumps

The iSN-713-MRTU is a compact vibration sensor module that combines a built-in three-axis MEMS accelerometer with an RS-485 interface. It is designed for condition monitoring of rotating and reciprocating plant, where a controller or host system needs regular vibration readings from a single device.Data is read over a single RS-485 port using Modbus RTU slave commands, so the module can be polled by any Modbus RTU master. The ±8g amplitude range and 6 Hz ~ 1 kHz frequency range make it suitable for low-frequency vibration measurement on production line equipment, motors and pumps.The module runs from a +10 ~ +30 VDC supply and can be fixed by wall-mounting or by magnet adsorption, which speeds up installation on steel machinery. It is rated for operation from -25 °C ~ +75 °C and is listed with CE, UKCA, FCC, RoHS and WEEE certification.ApplicationsVibration monitoring systemFactory condition monitoring of production line equipmentMotor and pump vibration monitoringReal-time vibration detection at critical locations

The iSN-713-MRTU-IP68 CR is a vibration sensor module for monitoring equipment condition in harsh industrial settings. Its built-in three-axis MEMS accelerometer measures vibration across X, Y and Z axes, and its IP68 rating protects the housing against water, oil and dust.Readings are delivered over a single RS-485 port using the Modbus RTU slave protocol. A host or PLC can poll the vibration data with standard Modbus RTU commands, with selectable baud rates from 9600 to 115200 bps and a fixed N, 8, 1 data format. The module suits real-time detection on critical machinery such as production line equipment, motors and pumps.The unit mounts by wall-mount or magnet adsorption and runs from a +10 ~ +30 VDC supply at 0.3 W. It is rated for an operating temperature of -25 °C ~ +75 °C.ApplicationsVibration monitoring systemsReal-time vibration detection on motors and pumpsFactory monitoring of production line equipment

SG-3037-G conditions the voltage output of a triaxial accelerometer so that all three axes can be read by downstream acquisition hardware. Each of the three input channels accepts a 0-24 V signal and delivers a corresponding ±10 VDC analogue output, keeping the vibration data in a form that standard I/O modules can digitise.The unit also supplies the 24 VDC excitation voltage needed by the accelerometer, so no separate sensor supply is required. With a 50 kHz signal bandwidth, it suits vibration measurement work where fast changes in the signal need to be preserved. Reverse polarity protection and EFT, ESD and surge immunity ratings help it tolerate demanding installation conditions.The SG-3037-G ordering code is the RoHS-compliant variant. It mounts on DIN-rail or on a wall and operates from -25 to +75 °C, making it practical for control cabinets and remote monitoring points alike.ApplicationsData acquisition systemsRemote diagnosisVibration measurementTesting equipment

SG-3227 CR is a two-channel signal conditioner for IEPE accelerometers. Each channel is set independently through its own DIP-switch bank, so one module can be matched to different sensors without changing hardware.Excitation current is selectable at 2 mA, 4 mA, 6 mA or 10 mA, and the built-in amplifier offers ×1, ×10 and ×100 gain to suit different signal levels. LED indicators show whether the sensor is operating normally, open circuit or short circuit, which helps locate wiring faults quickly during commissioning and fieldwork.The module outputs ±10 V analogue voltage on each channel, takes a +18 to +30 VDC supply with reverse polarity protection, and mounts on DIN-rail or wall. Two CA-BNC001 BNC adaptors are included with each unit.ApplicationsVibration measurementRemote diagnosisTesting equipment