Läckagedetektering

180° Hold-Down Clip (include 50 pcs).

90° Hold-Down Clip (include 50 pcs).

CA-LLD-DC100-L010 is a 1 m liquid leak detection cable for monitoring large areas where leaks may travel along an unpredictable route. Its sensing wires make it a practical choice for open floors and surfaces with several possible leak points, rather than a single fixed sensing spot.The cable has a 6 mm fluoropolymer carrier. Its sensing wires are 2 × 30 AWG, enclosed in a conductive fluoropolymer jacket. It can be fixed directly to water supply and return lines, so it can cover pipework as well as the surrounding floor area. The maximum continuous operating temperature is 70 °C.This ordering code is the without position variant, supplied in a 1 m length. It is RoHS and WEEE certified.ApplicationsLeak detection in open areasMonitoring water supply and return linesCovering larger surface areas with multiple potential leak points

CA-LLD-DC100-L030 is a 3M liquid sensing cable for detecting leaks across a wide area when the likely leak path cannot be predicted in advance. It suits open floor areas and larger surfaces where several leak points may appear.The cable can be run directly along water supply and return lines, so it can cover pipework without a dedicated sensor installation at each joint. Its 6 mm fluoropolymer carrier houses two 30 AWG sensing wires with a conductive fluoropolymer jacket.Designed for continuous operating temperatures up to 70°CSupplied in 3M length, identified by the -L030 suffixRoHS and WEEE certifiedApplicationsLeak detection along water supply and return linesOpen areas and larger surfaces with multiple potential leak pointsWide-area water leak monitoring where the leak path is not predetermined

CA-LLD-DC100-L100 is a 10M liquid leak detection cable for monitoring larger surface areas where the route a leak will take is hard to predict. Its length and flexible layout suit open areas and installations with several possible leak points.The cable can be fixed directly to water supply and return lines, so it can be routed along pipework to cover the areas where leaks are most likely to occur. It is supplied in the 'w/o Position' variant listed by the manufacturer.Construction is a 6 mm fluoropolymer carrier with two 30 AWG sensing wires enclosed in a conductive fluoropolymer jacket. The maximum continuous operating temperature is 70°C. The product is listed as RoHS and WEEE compliant.ApplicationsOpen areas with a wide surface to monitorWater supply and return linesLarger surface areas with multiple potential leak points

The CA-LLD-DC100-L300 is a 30 m liquid leak detection cable designed to cover larger areas where the path a leak might take is hard to predict. It suits open spaces with several possible leak points and can be fixed directly to water supply and return lines.Built with a 6 mm fluoropolymer carrier and two 30 AWG sensing wires enclosed in a conductive fluoropolymer jacket, the cable is rated for a maximum continuous operating temperature of 70 °C. This ordering code is the version without position detection.The cable is RoHS and WEEE compliant.ApplicationsWater leak detection over open or large surface areasMonitoring multiple potential leak pointsFixing to water supply and return lines

The CA-LLD-DC100-L500 is a liquid leak detection cable designed to monitor a wide area where the path a leak might take cannot easily be predicted. It suits open areas and larger surfaces with several possible leak points.The cable can be fixed directly to water supply and return lines, so it can follow the pipework rather than relying on a fixed sensor position. This version is supplied without position detection, as indicated by the 'w/o Position' designation in its description.The 6 mm cable uses a fluoropolymer carrier and two 30 AWG sensing wires with a conductive fluoropolymer jacket. It is rated for a maximum continuous operating temperature of 70 °C and is RoHS and WEEE listed.ApplicationsWater supply and return line leak monitoringOpen areas and large surfaces with multiple potential leak points

The CA-LLD-DC100X-L010 is a 1 m liquid leak detection cable for covering wide, open areas where the likely leak path cannot be predicted in advance. It can be run alongside liquid supply and return lines, and it suits larger surfaces with several potential leak points.Compared with the standard CA-LLD-DC100-Lxxx cable for iSN-101/104, this variant adds two functions when used with the CA-LLD-DC100X-TR terminal resistor. Cable-break detection reports a broken signal leader cable or detection cable immediately and passes the alarm to the iSN-101/104 buzzer. Snap-in connectors at both ends allow several detection cables to be connected in series.The signal leader cable plus all detection cables can reach a maximum of 500 m. The 6 mm fluoropolymer-jacketed cable carries two 30 AWG sensing wires and is rated for a maximum continuous operating temperature of 70 °C.ApplicationsLiquid leak detection over wide or open areasMonitoring liquid supply and return linesLarger surface areas with multiple potential leak points

The CA-LLD-DC100X-L030 is a 3 m liquid leak detection cable suited to monitoring large or open areas where the likely leak path cannot be predicted in advance. Its snap-in connectors allow the cable to be joined in series, so coverage can be extended without a fixed layout.Compared with the original CA-LLD-DC100-Lxxx cable, this variant adds cable-break detection and series connection. The source positions it alongside the iSN-101/104 detectors and the CA-LLD-DC100X-TR terminal resistor. Cable-break detection reports a broken signal leader cable or detection cable, and the cable can be connected directly to liquid supply and return lines.The 6 mm fluoropolymer-carried cable uses 2*30 AWG sensing wires with a conductive fluoropolymer jacket and has a maximum continuous operating temperature of 70°C. The signal leader cable plus all detection cables can reach up to 500 metres in total.ApplicationsLiquid leak monitoring over wide or open areasSurfaces with multiple potential leak pointsLiquid supply and return lines

CA-LLD-DC100X-L050 is a 5M liquid leak detection cable for monitoring wide, open areas where the path a leak will take is hard to predict. It can be run to the liquid supply and return lines directly, which suits larger surfaces with several possible leak points.Compared with the original CA-LLD-DC100-Lxxx cable for iSN-101/104, this variant adds cable-break detection and can be connected in series. Any break in the signal leader cable or the detection cable is reported immediately to the alarm buzzer of the iSN-101/104. Snap-in connectors at both ends let several detection cables be chained together.Cable-break detection alerts the iSN-101/104 alarm buzzerSnap-in connectors allow multiple detection cables to be linked in seriesSignal leader cable plus all detection cables can reach up to 500 metresMaximum continuous operating temperature of 70°CApplicationsLiquid leak detection over wide or open areasMonitoring along liquid supply and return linesLarger surfaces with multiple potential leak points

The CA-LLD-DC100X-L100 is a 10 m liquid leak detection cable for monitoring wide areas where the likely leak path is hard to predict. It suits open sites and larger surfaces with multiple possible leak points, and it can be connected directly to liquid supply and return lines.Compared with the original CA-LLD-DC100-Lxxx detection cable, this version can be joined in series and reports cable breaks. When used with the CA-LLD-DC100X-TR terminal resistor, a break in the signal leader cable or a detection cable is reported immediately to the iSN-101/104, which sounds its alarm buzzer.Snap-in connectors at both ends let several detection cables be chained together. The signal leader cable and all detection cables together can cover up to 500 m.ApplicationsLiquid leak detection over open areasMonitoring larger surface areas with multiple potential leak pointsLeak monitoring at liquid supply and return lines

The CA-LLD-DC100X-L300 is a 30 m liquid leak detection cable for monitoring wide areas where the likely leak path cannot be predicted in advance. Its layout suits open sites with several potential leak points.Unlike the standard DC100 cable, this variant adds cable-break detection and snap-in connectors at both ends, so several detection lines can be joined in series. The signal leader cable and all detection cables together can cover up to 500 m. Cable breaks in the signal leader or the detection cable are reported to the iSN-101/104 alarm buzzer.The cable can be connected directly to liquid supply and return lines. Its fluoropolymer carrier and conductive fluoropolymer sensing jacket are rated for a maximum continuous operating temperature of 70 °C.ApplicationsLiquid leak monitoring over large or open surface areasDetection along liquid supply and return linesSites with multiple potential leak points

The CA-LLD-DC100X-L500 is a 50 m liquid leak detection cable for covering wide, open areas where the path a leak will take is hard to predict. It can be run alongside liquid supply and return lines and suits surfaces with several potential leak points.Compared with the original CA-LLD-DC100-Lxxx cable, this variant adds cable-break detection and can be chained with other detection cables. A break in the signal leader cable or the detection cable is reported immediately to the alarm buzzer of the iSN-101/104 unit.The cable has snap-in connectors at both ends, so several detection cables can be joined in series to extend coverage. The signal leader cable and all detection cables together can reach up to 500 m.Fluoropolymer carrier, 6 mm cable diameterSensing wires: 2 x 30 AWG with conductive fluoropolymer jacketMaximum continuous operating temperature 70 °CRoHS and WEEE certifiedApplicationsLiquid leak detection over larger surface areas with multiple potential leak pointsOpen areas where the path of a leak cannot be predictedMonitoring around liquid supply and return lines

CA-LLD-DC100X-TR is a 2MΩ terminal resistor that fits the end of a liquid leakage detection cable run. The original CA-LLD-DC100-Lxxx detection cable on iSN-101/104 units cannot report a cable break and cannot be wired in series, so this resistor is used to add both capabilities.With the terminal resistor fitted, a break in the signal leader cable or the detection cable is recognised immediately, and the iSN-101/104 raises the alarm buzzer at the same time. Detection cables use snap-in connectors at both ends, so several lines can be joined in series to extend coverage.The signal leader cable and all connected detection cables can cover a maximum distance of 500 metres, which suits longer or more irregular layouts where a single fixed-length cable is impractical.ApplicationsLiquid leakage detection along extended or segmented cable runsMonitoring with iSN-101/104 units where cable-break alarms are required

CA-LLD-DP100 CR is a liquid leakage probe for detecting leaks at a specific location and at a defined water level. Its base carries two probes, and an alarm is raised only when liquid touches both of them at the same moment, closing the circuit between them.Because detection depends on that two-point contact, the probe suits areas where a leak must be picked up at a known height rather than anywhere on a floor. It is intended for drains, water storage tanks, containers and other restricted areas where an early warning of liquid is needed.The unit is RoHS and WEEE certified. Check the installation point against the water level you need to monitor before fitting it.ApplicationsDrainsWater storage tanksContainersOther restricted areas where liquid leakage must be detected

CA-LLD-EC-L030 is a 3 m leader cable for ICP DAS liquid leakage detection installations. It forms the first section of the sensing run and is designed to be extended in the field where the layout requires more reach.The leader cable accepts extension with shielded twisted pair cable in AWG 18~14. The total cable length, counting the leader cable and the sense cables together, must not exceed 500 m.The cable is listed as RoHS and WEEE compliant, which helps with documentation for European projects.ApplicationsLiquid leakage detectionDistributed leak sensing runs with extended sense cabling

The iSN-101 CR is a wall-mount liquid leak detector that switches its own relay output when water is detected, so it can drive a local alarm or signal a building or monitoring system without an external converter.It accepts either a point probe for spot monitoring or a line sense cable for longer runs, with total cable length of up to 500 m. Sensitivity is set with a rotary switch, and the module includes a buzzer with a push button to silence it. Cable-break detection is available when used with the CA-LLD-DC100X-Lxxx sense cable.Communication is via a single RS-485 port that supports Modbus RTU or DCON, with software-configurable baud rates from 1200 to 115200 bps. For Modbus RTU networks, the device address can be set in hardware, and the module can be paired with the WISE IoT Edge Controller or TPD/VPD Touch HMI.ApplicationsWater pipe leak monitoring in buildings, including water, fire and sewage pipesReal-time leak detection in computer rooms, base stations, warehouses, libraries and museumsMonitoring air handling equipment, refrigeration units, liquid containers and pump tanksIndustrial sites where equipment leakage must be detected and alarmed remotely

The iSN-101/DIN is a single-channel leak detection module for DIN-rail mounting. It monitors water with either a point probe or a line sense cable and switches its relay output when liquid is detected, so an alarm can be passed directly to a controller or monitoring system without an additional conversion module.Engineers can pick this variant when the module must sit in a control cabinet rather than on a wall. Sensitivity is set with a rotary switch within 26 KΩ to 580 KΩ, and the module provides an audible alarm with a push button to mute it. Cable-break detection is available when the CA-LLD-DC100X-Lxxx sense cable is used.For network integration, the module communicates over one RS-485 port using Modbus RTU or DCON, with baud rates from 1200 to 115200 bps set in software. It is powered from 10 to 30 VDC with reverse polarity protection.ApplicationsWater pipe leak monitoring in buildings, including water, fire and sewage pipesDetection of leakage from domestic water, drainage and electrical equipmentComputer room base stations, warehouses, libraries, museums and industrial sitesAir handling equipment, refrigeration units, liquid containers and pump tanks

The iSN-101/S CR is a single-channel liquid leak detection module that switches its own relay output when liquid is detected, so it can drive a local or remote alarm without an extra conversion module. Its RS-485 port supports Modbus RTU or DCON, which makes it straightforward to pass alarm status to a monitoring system or collection host on the network.The module accepts either a point probe or a line sense cable, and the total cable length can reach 500 metres including extension cables. Sensitivity is set with a rotary switch across 26 kΩ to 580 kΩ, and an on-board buzzer sounds on a leak and can be muted with a push button. Power and alarm LEDs show the module status at a glance.This /S variant is supplied with a 1 m liquid leak detection cable and a 3 m extended cable, as listed in the price list description for this ordering code.ApplicationsWater pipe leak monitoring in buildings, including water, fire and sewage pipesLeak detection near domestic water, drainage and electrical equipmentReal-time leak detection in computer rooms, base stations, warehouses, libraries and museumsMonitoring air handling equipment, refrigeration units, liquid containers and pump tanksIntegration with WISE IoT Edge Controller or TPD/VPD Touch HMI

The iSN-101/S/DIN CR is a 1-channel liquid leak detector that switches its own relay when water is sensed, so it can drive a local alarm or signal a remote system without an additional converter. It is designed for point detection with a probe or line detection with a sense cable, and it suits monitoring in buildings, plant rooms and equipment areas where early warning of water ingress matters.Sensitivity is set on a rotary switch across 26 KΩ to 580 KΩ, and the module provides an audible buzzer that can be silenced with a front push button. Its single SPST Form A relay makes the alarm state available to building management, PLCs or other collection hosts. Leak detection cable runs of up to 500 metres are supported, including the extended cables, and cable-break detection is available when used with the CA-LLD-DC100X-Lxxx sense cable.For networked monitoring, the module communicates over one RS-485 port using Modbus RTU or DCON, with software-configured baud rates from 1200 to 115200 bps. This DIN-rail variant is supplied with a 1m liquid leak detection cable and a 3m extended cable, and it operates from a 10 to 30 VDC supply.ApplicationsWater pipe leak monitoring in buildingsMonitoring of water, fire and sewage pipesDetection of leaks around domestic water, drainage and electric equipmentReal-time leak detection in computer rooms, warehouses, libraries and museumsMonitoring of air handling equipment, refrigeration units, liquid containers and pump tanks

The iSN-101/S2 CR is a standalone 1-channel liquid leak detector that switches its own relay output when liquid is detected, so it can drive local or remote alarms without an additional conversion module. Its RS-485 port supports Modbus RTU and DCON, allowing it to report status to a supervisory system or collection host on the network.Sensing is handled by a double-core leader cable of up to 500 m, or by point probes at fixed risk locations. Sensitivity is set with a rotary switch across 26 KΩ to 580 KΩ, and the module also raises an audible alarm that can be silenced with a push button. Modbus RTU device addresses can be configured in hardware.This variant is supplied with a 3 m liquid leak detection cable and a 3 m extended cable. The module is designed for wall mounting and operates from a 10 to 30 VDC supply across -25 to +75 °C.ApplicationsWater pipe leak monitoring in buildingsDetection of leakage from fire pipes and sewage pipesDomestic water, drainage and electrical equipment monitoringComputer room base stations, warehouses, libraries and museumsAir handling equipment, refrigeration units, liquid containers and pump tanks

iSN-101/S2/DIN is a single-channel liquid leak detector that switches its own relay when water is detected, so it can drive an alarm or control circuit without an external converter. It has a DIN-rail mounting option and an RS-485 port, which lets it report to a monitoring system using Modbus RTU or DCON.The module supports point detection with a probe or line detection with a sense cable, and the total cable run can reach 500 metres including extension cables. Sensitivity is adjustable across 26 kΩ to 580 kΩ with a rotary switch, and a buzzer sounds on alarm, which can be silenced with a push button.This ordering code includes a 3m Liquid Leak Detection Cable and a 3m Extended Cable. Cable-break detection is available only with the CA-LLD-DC100X-Lxxx sense cable.ApplicationsWater pipe leak monitoring in buildingsDetection of leaks in domestic water, fire and sewage pipes and drainageLeak monitoring near electric equipmentComputer room base stations, warehouses, libraries and museumsAir handling equipment, refrigeration units, liquid containers and pump tanksIntegration with the WISE IoT Edge Controller or TPD/VPD Touch HMI

The iSN-101/S3 CR is a compact liquid leak detection module that switches its own relay output when water is detected, so it can drive alarms or control equipment without an additional conversion module. Its single channel suits point detection with a probe or line detection with a sense cable.The module can monitor sense cables of up to 500 meters, including the liquid leak detection cable and extended cables. Sensitivity is adjustable by rotary switch across a range of 26 KΩ ~ 580 KΩ. A buzzer sounds on detection and can be silenced with the push button, while two LEDs show power and alarm status.Communication is over one RS-485 port using Modbus RTU or DCON, with software-configured baud rates from 1200 to 115200 bps. This allows the module to be integrated with networked collection hosts and monitoring systems for remote alarm and device control.ApplicationsWater pipe leak monitoring in buildings, including water, fire and sewage pipesReal-time leak detection in computer room base stations, warehouses, libraries, museums and industrial sitesMonitoring air handling equipment, refrigeration units, liquid containers and pump tanksDetection in domestic water, drainage and electrical equipment areas

The iSN-101/S3/DIN CR is a single-channel liquid leak detection module for DIN-rail mounting. It monitores a water sense probe or cable and switches a Form A relay when liquid is detected, so a local alarm or a supervisory system can respond without an additional conversion module.Communication runs over one RS-485 port using either Modbus RTU or DCON, with software-configured baud rates from 1200 to 115200 bps. Sensitivity from 26 KΩ to 580 KΩ is set with a rotary switch, and a push button mutes the buzzer. Cable-break detection applies only to the CA-LLD-DC100X-Lxxx sense cable.Detection cable and extension cables can total up to 500 meters. The unit operates from 10 ~ 30 VDC with reverse polarity protection. It is listed with CE, UKCA, FCC, RoHS and WEEE, and the source notes it can be combined with the WISE IoT Edge Controller or TPD/VPD Touch HMI.ApplicationsWater pipe leak monitoring in buildingsWater, fire and sewage pipe monitoringComputer room base stations, warehouses, libraries and museumsAir handling equipment and refrigeration unitsLiquid containers and pump tanks